How to Hook Up Carburetor Hoses to Yamaha Ttr 125

How to Hook Up Carburetor Hoses to Yamaha Ttr 125

Introduction

Are you new to Yamaha Ttr 125s? If so, you may wonder how to hook up the carburetor hoses. This article will show you where each hose goes and how to connect them. Once you have connected the hoses, you can start your bike and see how it runs. Happy riding! We will explore how to hook up carburetor hoses to Yamaha TTR 125.

How to Hook Up Carburetor Hoses to Yamaha Ttr 125

Tools We Need to Hook Up Carburetor Hoses to Yamaha Ttr 125

Before you can hook up the carburetor hoses to your Yamaha Ttr 125, you’ll need to gather a few tools. First, you’ll need a screwdriver to remove the carburetor’s air filter cover. Next, you’ll need a pair of pliers to disconnect the fuel line from the carburetor. Finally, you’ll need a wrench to loosen the clamps that secure the carburetor to the intake manifold. With these tools in hand, you’ll be ready to hook up the carburetor hoses and get your Yamaha Ttr 125 running like new again.

How to Hook Up Carburetor Hoses to Yamaha Ttr 125

Before beginning, inspect your Yamaha Ttr 125 for any damage. If you find any leaks, make sure to repair them before continuing. Once you have ascertained that your Yamaha Ttr 125 is in good working order, begin the process of hooking up the carburetor hoses by following these six steps:

  • Remove the air filter cover and unscrew the four screws that hold the carburetor in place.
Remove the Air Filter Cover
  • Carefully remove the carburetor and set it aside. Be sure not to lose any of the small parts inside.
Carefully Remove the Carburetor
  • On the back of the carbs, locate the two fuel hoses and disconnect them from the fittings.
  • Examine the hoses for cracks or damage and replace them if necessary.
  • Reconnect the fuel hoses to the fittings on the back of the carburetor, making sure they are tight.
Reconnect the Fuel Hoses
  • Screw the carburetor back into place and replace the air filter cover. Be sure all screws are tightened securely.
    An expert rider will be able to complete this process in a matter of minutes; however, if you are new to working on Yamaha Ttr 125s, take your time and be careful not to drop any small parts or strip any screws. With a little patience, you’ll have your bike running like new in no time!

Tips to Hook Up Carburetor Hoses to Yamaha Ttr 125

Carburetors are one of the most important engine components, and proper installation is critical to ensuring optimal performance. When installing carburetor hoses on a Yamaha TTR 125, there are a few tips to keep in mind. First, be sure to connect the hoses according to the manufacturer’s instructions.

Second, use high-quality clamps to secure the hoses in place. Third, make sure that there are no leaks at the connections. fourth, route the hoses so that they are not damaged by moving parts. Fifth, check all connections for tightness before starting the engine. By following these tips, you can be sure that your carburetor hoses are properly installed and that your engine will perform at its best.

What is the Size of Yamaha TTR 125 Carburator

The TTR 125 carb has a size of 20mm. It is a four-stroke, air-cooled, SOHC, 2-valve engine. The bore x stroke is 52.4mm x 49.5mm. The compression ratio is 10.0:1. The carburetor is a CV type with a throttle position sensor (TPS). The ignition system is CDI with an electronic advance. The starter system is electric with a kick-start backup.

The clutch is a wet multi-plate type with coil springs. The transmission is a 5-speed constant mesh with a chain drive. The final drive is by the #428 chain. The frame is a semi-double-cradle steel frame with an aluminum swing arm. The suspension front/rear is telescopic fork/link mono-shock with adjustable preload and rebounds damping.

The wheelbase is 1,285mm (50.6in), the ground clearance is 345mm (13.6in), and the seat height is 805mm (31.7in). The fuel capacity is 7 liters (1.85 US gal). The tires front/rear are 70/100-19 / 90/100 R17M/C 54S tubeless tires. Brakes front/rear are hydraulic single disc brakes with dual-piston calipers and sintered pads..source:https://www.bikez.com/motorcycles/yamaha_ttr_125_2006.php#specs

FAQ

How Do You Adjust the Idle on a Yamaha TTR 125?

The Yamaha TTR 125 is a great motorcycle for beginners. It is small, lightweight, and easy to handle. But like all motorcycles, it needs to be tuned up from time to time. One of the most important things you can do to keep your TTR running smoothly is to adjust the idle. Here’s how:

First, make sure the motorcycle is turned off and cooled down. Then, remove the seat so you can access the carburetor. Locate the idle adjustment screw on the side of the carburetor and turn it clockwise until it is tight. Next, start the engine and let it warm up for a few minutes.

Finally, turn the idle adjustment screw counterclockwise until the engine is running at a smooth idle. Check the owner’s manual for more detailed instructions if needed. With a little bit of care and maintenance, your Yamaha TTR 125 will provide years of enjoyment.

How Do You Remove the Choke Cable on a TTR 125?

To remove the choke cable on a TTR 125, first, disconnect the cable from the carburetor. Next, loosen the clamp that secures the cable to the handlebar. Then, pull the cable out of the housing. Finally, unscrew the cable from the choke lever. Once the choke cable is removed, you can clean it and inspect it for wear. If the cable is damaged, it will need to be replaced.

Conclusion

In conclusion, it is important that you take the time to properly connect the carburetor hoses to your Yamaha TTR 125. If you follow these simple steps, you will have everything connected correctly and your bike should run smoothly. Be sure to double-check all of your connections before starting the engine, and don’t hesitate to ask a friend for help if you are unsure about anything. With just a little bit of effort, you can get your bike up and running in no time! we have explored how to hook up carburetor hoses to Yamaha TTR 125.

You may read also – How Much Piston Scoring is Acceptable

6 thoughts on “How to Hook Up Carburetor Hoses to Yamaha Ttr 125”

  1. Pingback: How Much Oil Does a YZ250F Take (Useful Information)

Leave a Comment

Your email address will not be published. Required fields are marked *